Working with music or a recorder may impose a lot of concerns specifically on its volumes. For example, when doing a voice over, your recorded audio may be overpowered by a background music. To settle the needs for this adjustment, you should have a device that is deemed as a variable resistor. This device may also be applicable if you would like to take measurements for deflections on performing centers or when you wish to reduce the noise you are experiencing in your motorbike.
In some cases, devices which involve circuitry and an equation are produced as an aid to these situations. Known as the most fundamental circuit, this tool is called a Voltage Divider. It is a passive circuit which helps reduce the large volumes of your audio equipment or other electronics.
With three variables namely two resistors and an initial voltage, you can already turn a large Volt count into a smaller one which is considered as the output Volt. To simplify this, you could understand the process better using a certain equation. This equation is basically a representation of the Ohms law which observes a direct proportion relationship between a current and the difference of ends. Having said so, it is understood that as the current is reduced by the attached divider in between two resistances, the voltage released is also lowered.
There are two essential parts of this divider, one is the circuit and the other is the equation. The circuit pertains to a source of the Volt which goes across two resistors. For the equation, you have to assume three values namely input voltage, resistor one R1, and resistor two R2. The output value could be found by taking the ratio between R1 and R2.
You can also create your own device if you wish to but you have to be mindful that when creating your portable gear. Most simple electronics can only withstand 5V, however, most sources like for example your remote control, a standard 9V battery will do. To do so, first, you should prepare the specific tools needed such as your leads, resistors, your battery, three alligator clamps, connectors and your voltmeter.
Start by connecting one lead to a red lead of a 9V battery with an alligator clamp. Then using another lead, do the same steps but this time using the black lead of the connector. After, you can twist the free end of each resistor together.
Putting together the two leads. Twist together both lead ends and lock it up using the last alligator clamp. After doing so, take the connector of your voltmeters then do the correct terminal placing. Red wires go to the positive terminal of your battery while the black wires refer to the negative one. Then you can start turning your meter on.
As you can see from 9V, your voltage goes down to 3V. When this happens, the positive terminal of the circuit is now the one where the twist is located. Meanwhile, the negative terminal is retained as the negative source.
Before going through this procedure, unhook the end of the divider. In some case, you have to unplug your battery to avoid draining. For this procedure, your 9V energy source does not really show a lot of danger. But, when working with some other electronics, make sure to unplug the wires from wall outlets as this may cause electrocution.
In some cases, devices which involve circuitry and an equation are produced as an aid to these situations. Known as the most fundamental circuit, this tool is called a Voltage Divider. It is a passive circuit which helps reduce the large volumes of your audio equipment or other electronics.
With three variables namely two resistors and an initial voltage, you can already turn a large Volt count into a smaller one which is considered as the output Volt. To simplify this, you could understand the process better using a certain equation. This equation is basically a representation of the Ohms law which observes a direct proportion relationship between a current and the difference of ends. Having said so, it is understood that as the current is reduced by the attached divider in between two resistances, the voltage released is also lowered.
There are two essential parts of this divider, one is the circuit and the other is the equation. The circuit pertains to a source of the Volt which goes across two resistors. For the equation, you have to assume three values namely input voltage, resistor one R1, and resistor two R2. The output value could be found by taking the ratio between R1 and R2.
You can also create your own device if you wish to but you have to be mindful that when creating your portable gear. Most simple electronics can only withstand 5V, however, most sources like for example your remote control, a standard 9V battery will do. To do so, first, you should prepare the specific tools needed such as your leads, resistors, your battery, three alligator clamps, connectors and your voltmeter.
Start by connecting one lead to a red lead of a 9V battery with an alligator clamp. Then using another lead, do the same steps but this time using the black lead of the connector. After, you can twist the free end of each resistor together.
Putting together the two leads. Twist together both lead ends and lock it up using the last alligator clamp. After doing so, take the connector of your voltmeters then do the correct terminal placing. Red wires go to the positive terminal of your battery while the black wires refer to the negative one. Then you can start turning your meter on.
As you can see from 9V, your voltage goes down to 3V. When this happens, the positive terminal of the circuit is now the one where the twist is located. Meanwhile, the negative terminal is retained as the negative source.
Before going through this procedure, unhook the end of the divider. In some case, you have to unplug your battery to avoid draining. For this procedure, your 9V energy source does not really show a lot of danger. But, when working with some other electronics, make sure to unplug the wires from wall outlets as this may cause electrocution.
About the Author:
When you are searching for the facts about a voltage divider, come to our web pages. More details are available at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
No comments:
Post a Comment